VANE MIXER

Лопастной смеситель — это машина, которая используется для смешивания минеральных продуктов и предварительно смешанных продуктов с однородно дозированными и измельченными зернами. Это обеспечивает более быстрое смешивание, но требует большей мощности, а нагрузка должна быть равномерной.
Лопастной смеситель La Meccanica гарантирует получение однородных смесей с коэффициентом вариации <5%. Однородность достигается через небольшой промежуток времени (2-3 минуты). Можно добавлять жидкости, а время наполнения и выгрузки очень короткое.

  • Наш смеситель имеет следующие технические характеристики

    • Точность обеспчивает однородные смеси с коэффициентом варьирования <5%.
    • Однородность достигается спустя короткое время (2-3 минуты).
    • Смешанный материал тщательно обрабатывается.
    • Во время разгрузки в смесителе не остается никаких остатков (точность заслонки, риск перекрестного заражения).
    • Возможность добавления жидкостей
    • Очень короткое время заполнения и разгрузки
    • Варьируемая величина допуска

Specifications

Feed industry
Main motor power
Cattle feed
CLM 200 20hp
7.7 - 11.0 - 15.0 kW - 6 pole
150 kg / h
CLM 304 60hp
30 - 37 - 45 kW - 4 pole
1.5 Ton / h
CLM 420 75hp
37 - 55 kW - 4 pole
2.5 Ton / h
CLM 420 125hp
75 - 90 kW - 4 pole
4.0 Ton / h
CLM 420 150hp
110 kW - 4 pole
6.0 Ton / h
CLM 420 Twin Motors
55 × 2 kW
6.0 Ton / h
CLM 520 180hp
10 - 132 kW - 6 pole
8.0 Ton / h
CLM 520 220hp
160 kW - 6 pole
9.0 Ton / h
CLM 520 Twin Motors
90 × 2 kW
9.0 Ton / h
CLM 630 220hp
160 kW - 6 pole
10.0 Ton / h
CLM 630 300hp
200 - 220 kW - 6 pole
12.0 Ton / h
CLM 630 Twin Motors
110 × 2 kW
12.0 Ton / h
CLM 800 380hp
250 - 280 kW - 6 pole
18.0 Ton / h
CLM 800 Twin motors
2x132kW
18.0 Ton / h
Тип Объем л. Макс.загрузка, кг Вес, кг Габаритные размеры    
L B H
MIP-500 500 310 870 2120 910 1210 SP-500-rev00.pdf SP-500-rev00.dwg
MIP-1000 1000 600 1450 2165 1230 1530 SP-1000-rev00.pdf SP-1000-rev00.dwg
MIP-2000 2000 1250 2200 3335 1490 1855 SP-2000-rev00.pdf SP-2000-rev00.dwg
MIP-4000 4000 2500 3800 3450 1890 2340 SP-4000-rev00.pdf SP-4000-rev00.dwg
MIP-6000 6000 3750 7200 4344 2172 2680 SP-6000-rev00.pdf SP-6000-rev00.dwg
MIP-8000 8000 5000 6800 4800 2172 2743 SP-8000-rev00.pdf SP-8000-rev00.dwg
MIP-10000 10000 6250 8500 5362 2172 2743 SP-10000-rev00.pdf SP-10000-rev00.dwg

Optional

The rollers are adjusted by a hydraulic piston driven by a hydraulic device located outside the machine and controlled from the control panel.

The position of the rollers is calculated by means of an angular potentiometer mounted behind the rollers (inside the main shaft). The potentiometer signals the angular position of the roller pins. By operating the entire system from the control panel, the distance between the rollers and the die can be calculated using the signal transmitted by the potentiometer.

At the electronic panel, the operator chooses the roller position. The panel pressurizes the hydraulic circuit and moves the piston until the rollers reach the desired position.

From the electrical panel, the operator determines the position of the rollers by applying pressure to the hydraulic system and moving the piston until the rollers reach the desired position. Once the desired position has been reached, the system is locked and held in position by two valves.

The maximum pressure reached by the hydraulic system is 250 bar, and the required pressure for moving the piston and adjusting the rollers is 150 bar.

The adjustment is done quite quickly: you can move the rollers closer or further away from the matrix by 7-8 mm, in each direction in about 15 seconds.

For more information, watch the following video: Automatic Rollers Adjustment (WAP System)

rapid bloc quick device for change dies.jpgrapid bloc quick device for change dies-2.jpg

The device allows replacing the matrix in 10-20 minutes, depending on its size. The system includes a tapered stainless steel ring that is closed and held in place by Belleville disc springs.

This ring locks the die in place. The matrix is released by pressure on the hydraulic system, which pushes the springs to release the elastic ring.

For more information, watch the following video: Rapid Block System

hydraulic push off devices.jpg

The system consists of a hand pump and a piston, which are needed to dismantle the die.

The piston is installed between the rotor and the reinforcement flange so as to push the die out of its seat.

 

automatic lubrication system.jpg automatic lubrication system2.jpg

This system includes a high viscosity grease pump.

It is equipped with blades to break up possible air bubbles. The system is connected to the press via a rotary distributor connected directly to the main shaft.

Lubrication is controlled by an electrical panel that is included in the delivery. The panel allows you to measure the required amount of grease using two timers to regulate the time for applying grease and pause.

 

The pump has the following characteristics:

● the flow is adjustable from 2.9 to 17 cc / min.

● motor 0.185 kW, 400V, 50Hz

● steel tank for 10 kg

● filter

● pressure relief valve

● pressure gauge

● indicator of minimum lubricant level

● progressive dispenser for distributing grease at two points

● inductive PNP sensor for cycle monitoring

● control valves for 1/8 outlet